Domestic or foreign mid-size or
smaller cars.
No Honda's, Acura's or Saturn's.
No large Cadillac's, Buick's, Oldsmobile's, etc.
Doors cannot be cut out, except
for left side for door bars only.
No body chopping of any kind.
Fenders may be trimmed for tire
clearance.
Front and rear wheel wells may be
removed.
Stock dash is allowed.
No radios or mirrors.
Roof, door or center post cannot
be removed or altered in any way.
Rear wings or spoilers are
allowed, not to exceed 8 inches tall, and no wider
than top edge of body.
No skirting, side trim or open
hoods of any kind.
No added weight.
2. Seat and Belts:
MANDATORY - Racing seats with
5 point racing seat belts and window nets.
Aluminum racing seat.
REPLACE belts if older than three
years.
Belts newer than three years and
are showing wear, tear, or fraying, must be
replaced.
Subject to safety inspection at
any time.
3. Roll Cage:
Must consist of front and rear
loop with X in back loop.
Must be mounted to frame by angle
or tubing from front to rear and 1 bar at bottom of
rear loop side to side.
Must have at least 1 bar from
rear halo to rear hump and must have 2 left side
door bars and 1 right side door bar and must have 1
horizontal bar from side to side of front legs.
Must have metal plate on drivers
side extending 5 inches in front of seat and no
shorter than 24 inches wide and must be at least 18
gauge or .049 thickness.
Top four corners of cage must
have small gussets.
4. Windshield:
Screen maximum 2" x 4" or 5 bars
minimum 3/8" from center to left side post.
5. Engines:
4 cylinder only -- no SHO-SVO
V-Tec or high performance motor parts.
No turbos -- No Exceptions!
No aftermarket brains, proms, or
chips and NO altering stock ones.
Aftermarket air cleaners are
allowed by inspection.
There will be a $100.00 claim on
computer and brain boxes.
DO NOT RUN OVER FLOW TUBE OUT
PASSENGER DOOR AREA
6. Fuel:
Injection or carbureted.
Pump gas or racing fuel.
7. Battery:
It is optional to move battery
inside car or trunk but must be mounted securely.
(Highly recommended)
8. Fuel Tank:
Stock can be used if left in
stock location.
If fuel cell used there must be a
fire wall between fuel cell and driver.
9. Bumpers:
Stock bumper or tube.
Tube bumper requirements:
A. Must be built of maximum 1
1/2" OD and .120 thickness.
B. Consisting of 1 bar no longer
than center of tire to center of tire.
C. Ends must be turned towards
body, rounded with capped ends.
D. Bumper can consist of 1 top
loop and 1 bottom loop no taller than 16" top to
bottom and no wider than frame rails or frame horns.
E. Bumper can only be connected
to frame 1/2" bar per side; no bracing of any kind.
F. Legs can be only extended 10"
beyond core support. You may put small gussets where
legs and main bumper connect.
10. Transmissions:
Stock OEM standard or automatic.
No high performance clutches or
flywheels.
11. Modifications:
Absolutely no modifications of
car, engine, brakes or suspension.
12. Brakes:
Four wheel brakes mandatory.
13. Exhaust:
Stock exhaust must run past
driver.
Mufflers are not required.
14. Safety Equipment:
Complete fire suit and gloves of
flame retardant material must be factory labeled.
At least SA 2000 approved helmet
and racing shoes are required.
Neck collar and window net is
required in this class.
15. Tires and Wheels:
DOT tires only.
OEM steel or aluminum wheel only.
Maximum width 55 series and must
fit 8 ½" hoop.
Grooving allowed, but no mud
tires.
Any offset wheel allowed.
RIGHT FRONT — 60 series or wider
only with 40 lbs minimum air pressure.
Right front must durometer 45
after the main event, no cool off period.
All cars in top 5 will be checked
for durometer rule.
16. Restarts:
All restarts will be regular
single file with a cone.